스텝 수 너비 44 행 높이 에지 마스터M 슬레이브S

타이밍 차트 만들기

지금은 예제가 표시되어 있습니다. 고쳐 보며 시험하거나, [파일] → [새로 만들기]로 처음부터 시작하세요. 가입이 필요 없고, 만든 그림은 서버로 전송되지 않습니다.

아직 신호가 없습니다.
왼쪽 변수 목록의 항목을 두 번 클릭하거나 여기로 끌면 행이 추가됩니다.
변수가 아직 없다면 «가져오기…»로 Excel의 열을 붙여 넣거나, «추가…»로 하나씩 등록하세요.
AI 검토용 텍스트
변수 가져오기
Excel 표를 그대로 붙여 넣으세요. 첫 행이 머리글이면 이름, 형식, 코멘트, 방향 열을 자동으로 찾고 나머지 열(주소 관리 등)은 건너뜁니다. 머리글이 없으면 이름 / 형식 / 코멘트 / 방향 순서로 읽습니다 (BOOL은 형식을 생략해도 되고, 방향은 M, S, 내부, 또는 마스터 / 슬레이브 기기 이름입니다). CSV와 TSV 파일, 주소 맵 JSON도 이 창에 끌어다 놓을 수 있습니다.
주소 맵의 변수
변수 목록에 추가할 변수를 고르세요. 체크를 해제한 변수는 가져오지 않습니다.
대상 구획
이 차트가 다루는 구획을 선택합니다. 선택한 구획의 변수만 변수 목록에 표시됩니다. 아무것도 선택하지 않으면 전체입니다.

변수 추가
차트 정보
이 이름이 방향 열(M→S / S→M)과 순서도의 레인 이름을 정합니다. 도구 모음에서도 바꿀 수 있습니다.
ms 
일괄 내보내기
형식
    빠른 참조

    Rows and variables

    Double-click / EnterAdd the selected variable to the end of the chart (dragging works too)
    Drag the row numberReorder the rows
    Double-click the row labelEdit the name, type, direction and comment (right-click to duplicate, delete and more)
    DirectionM→S = driven by the master, S→M = driven by the slave. Set the device names in the “Master” and “Slave” fields of the toolbar (or in the chart info)
    Move panelsDrag a panel by its header (⠿) to the top or bottom of the left or right column, into tabs with another panel, or into a new column beside it (up to two columns on each side). ⋯ offers the same choices, and “Reset to default layout” puts everything back

    Waveforms

    Click / dragON/OFF on a BOOL row (drag sideways to paint)
    Double-click / F2Type a numeric or state value. Drag sideways from a filled cell to extend it
    Shift+click / arrowsSelect a range. The row number selects a row, the ruler selects a column, the top left selects everything
    Right-clickInsert or delete a step
    Edge (toolbar)Draw a BOOL transition vertical or sloped (a value change on a numeric or state row is always a crossing). Right-click a row label to set it for that row
    Right-click a row label → Draw as a waveformPlot a numeric row as a waveform instead of value blocks (an axis position, a timer, an analogue input). “Row display…” also sets the unit and the scale
    Select a range, right-click → Fill with a straight line (ramp)…Fill the range evenly from a starting value to an ending value

    Cause-and-effect arrows

    Arrow button / Alt+dragDrag from a corner of a transition (a ○ on the High and the Low corner) to the transition of the signal that reacts to it. Holding Alt shows the ○ too
    Build a flowchartWith arrows in place, the flow waits for exactly the input each arrow names before changing the output

    Files

    Auto-saveSaved in the browser and restored the next time you open it

    Output

    SVGAlways white background and black lines. On BOOL waveforms the horizontal and vertical lines are separate, so converting to shapes in Excel or Visio lets you move the vertical edges alone
    Draw.ioAlways white background and black lines. Step boundaries and row heights are aligned to the draw.io grid of 10 (sloped edges and waveform points fall between grid lines). The cause-and-effect arrows are not attached to the waveforms, so move them yourself when you move a waveform
    MarkdownA specification with the signal list, the timing table, the transitions, the cause-and-effect list and a sequence diagram (Mermaid). Paste it straight into Notion or GitHub
    MermaidOnly the sequence diagram, as Mermaid code (.mmd). Cases become alt, repeated spans loop

    The project file (.json) is shared with the C version, TimingChartEditor.exe.

    사용 설명서 — Timing Chart Editor

    Timing Chart Editor — User Guide

    Design the signal exchange between devices — PLC, microcontroller, host PC — as a timing chart, and produce the specification, the flowchart and a review text from that same chart.

    1. Overview

    The Timing Chart Editor is a drawing tool that feels like a spreadsheet: steps (slices of time) run across, signals run down, and you paint the waveform in the grid. BOOL signals are drawn as ON / OFF waveforms; numeric and state signals are drawn as blocks carrying their value (bus notation), and the points where the value changes are drawn as a crossing (><).

    It runs entirely in the browser, with no external libraries and no server. What you type is saved automatically inside the browser on this machine only, and is never sent anywhere. A finished chart can be exported as SVG for a specification, as Draw.io or as Markdown, and it can be handed to the Flowchart Editor in the same folder to draft the control flow automatically.

    2. Tutorial (your first chart)

    1. Type the device names into “Master” and “Slave” in the toolbar (for example PLC / Servo). They drive the direction column and the lane names in the flowchart.
    2. Press “Import…” above the variable list and paste your signal list from Excel. If the first row is a header, the name, type, comment and direction columns are found whatever their order.
    3. Double-click a variable (or drag it onto the chart) to add a row. Dragging the row number reorders the rows.
    4. Click or drag sideways on a BOOL row to paint the ON stretch. On a numeric row, double-click to type a value, then drag sideways from a filled cell to extend it.
    5. Press “Arrow” in the toolbar and drag from the transition of a request signal to the transition of the signal that answers it, to record the cause and effect.
    6. In “Output → Export…” (Ctrl+E) pick Markdown and press “Copy to clipboard”, then paste it into Notion or GitHub.

    “Tutorial” in the Help menu loads the sample and walks you through the same steps, highlighting each part of the screen as it goes.

    3. Drawing waveforms

    “Edge” in the toolbar decides how a BOOL transition is drawn. “Vertical” gives the ideal logic waveform; “sloped” is closer to a real signal, where rising and falling take time. To change a single row, right-click its label and pick “Edges”.

    Numeric and state rows (bus notation) always draw a value change as a crossing (><), as a timing chart should. That does not follow the “Edge” setting, and the width of the crossing follows the step width.

    4. Quantities that change continuously

    A specification often has to show the condition that makes a discrete signal change — when does “positioning complete” turn ON, above what pressure is “pressurised” reached. The quantity behind that condition — an axis position, a speed, an analogue input — changes continuously, and value blocks cannot draw it. Right-click the row label and pick “Draw as a waveform”, and the values are plotted against the height of the row. “Row display…” also sets the unit (mm, ms, V, rpm and so on) and the scale (the value at the bottom and at the top). Leave the scale empty and it follows the range of that row’s values; give several rows the same scale when you want to compare them.

    The values still live in the cells, so pasting from Excel, selecting a range, copying and undo all keep working. Instead of typing every step, select a range and use “Fill with a straight line (ramp)…” (right-click a cell, or the Edit menu) to fill it evenly from a starting value to an ending value. 0 → 100 rises, 100 → 0 falls. For a trapezoid, fill the rising range, the flat range and the falling range one after another.

    A waveform row changes value at nearly every step, so the ○ for a cause-and-effect arrow appears only where the movement starts, stops or turns round. That gives you arrows such as “start request ON → the axis begins to move”. The transition list in the Markdown export and the AI review text pick up the same points.

    Waveform rows are for display only and are not read when a flowchart is generated. What becomes a step or a wait is the BOOL signal that reacts to the waveform (positioning complete and the like).

    Shift+click and the arrow keys select a range, and Space (invert), 1 (ON), 0 (OFF) and Delete (clear) edit the whole selection at once. Ranges can be copied to and pasted from Excel.

    5. Cause-and-effect arrows

    An arrow records the relation “B changes only after A has changed”. While arrow mode is on (or while Alt is held), a small ○ appears at every transition — one on each of its two corners, High and Low — so grab whichever is nearer. A numeric or state signal has a single ○ at the centre of its crossing. Drag from the ○ of the cause to the ○ of the effect and release; the arrow points at the corner you grabbed. The effect must sit on the same step as the cause or later.

    Which corner of a transition an arrow uses, High or Low, is yours to choose. When several arrows meet in one place, spreading them between the two corners keeps the chart readable. The corner is kept in the JSON as level; leave it out and the level after the change is used.

    If you repaint a waveform and the transition disappears, the arrow is drawn as a dashed line in the warning colour. Either click it and press Delete, or fix the waveform.

    6. How to think about M→S / S→M

    Every signal carries a direction that says who drives it. M→S is driven by the master and received by the slave (requests, commands); S→M is driven by the slave and received by the master (responses, status); Internal is used inside one device only. Keeping the directions straight makes it obvious which program has to write what.

    The basic handshake has four steps: request ON → response ON → request OFF → response OFF. Changing the next signal only after the other side has answered (the interlock) is what prevents missed signals, double starts and timing-dependent faults.

    The arrows make that “confirm, then change” relation explicit on the chart. With the arrows in place, the flowchart is built so that it waits for exactly the input each arrow names before changing the output. Changes with no arrow — a timer, for instance — are simply laid out in step order.

    7. Import and export

    • Import: all in one place, under “File → Import…” — paste JSON, paste a table of variables, or open a file. Excel pastes, CSV / TSV and the JSON of the Memory Map Editor are all accepted, and address and initial-value columns are kept in the variable list.
    • Export: all in one place, under “Output → Export…” (Ctrl+E). Each format says where it is meant to be pasted, so you pick one and press “Copy to clipboard” or “Save to a file”.
    • Image (PNG): copy it and paste it straight into Word, Excel, PowerPoint, an e-mail or a chat.
    • SVG: a white-background, black-line drawing for a specification. The arrows are drawn too.
    • Draw.io: shapes that draw.io can edit. Press “Copy to clipboard”, then Ctrl+V in the draw.io window. A drawing changed in draw.io cannot be loaded back into this editor, so change the waveforms and arrows here and paste again.
    • Markdown: a specification containing the signal list, the timing table, the transitions, the cause-and-effect list and a sequence diagram (Mermaid).
    • Mermaid: only the sequence diagram, as Mermaid code (.mmd). Signals without a direction (M→S / S→M) become notes. Cases (branches) are written as alt / else, repeated spans as loop and named spans as a frame; time conditions follow the resulting signal.
    • AI review text: a tabular text for asking a generative AI to point out contradictions in the logic.

    If draw.io pastes it as plain XML text, add a new page with the + at the bottom left and choose Extras → Edit Diagram… on the menu bar (without the menu bar: + → Advanced on the toolbar). The box holds the XML of the current page: select it with Ctrl+A, paste, and press Apply. Apply replaces everything on the page, which is why a new page is used.

    8. Keyboard shortcuts

    9. Saving and handing over

    Your work is saved automatically in the browser and restored the next time you open the tool. To keep it as a file, press Ctrl+S and save the JSON. That JSON carries the schema shared across the platform (variables and triggers), so variables and cause-and-effect relations move between all four tools. Clearing the browser data also clears the automatic save, so always keep important charts as files.

    A machine usually has several timing charts, one per handshake. Use the “Chart ▾” list at the top to add, switch, duplicate and remove them. Once there are two or more (or once you receive variables with partitions from the Memory Map), the “This machine” tree appears on the left and takes over the list (click a chart to switch to it; use ⋯ in its header to add, duplicate or remove; click a device or block to show only that partition’s variables). It also lists the system diagram, memory maps and flowcharts of the same machine, and items marked ↗ open in their own tool. The tree and the variable list can be dragged by their headers to the top or bottom of the left or right column, into tabs with another panel, or into a new column beside it (also from ⋯). Once you use the list, New and Open keep the current chart in the list and add another one. “Save the whole list to a machine file…” puts them all in one file, and “Put all into the list” brings them back when you open a machine file.

    This is the third of the four design tools; the buttons at the right of the toolbar move you backwards and forwards.

    1. System Diagram Editor: decide the devices, blocks and networks
    2. Memory Map Editor: assign the variables and addresses (“← Memory Map” opens it; its “To Timing Chart →” sends the variables here)
    3. Timing Chart Editor (this tool): decide the movement in time and the cause-and-effect relations
    4. Flowchart Editor: “To Flowchart →” generates the flow with those relations applied

    For the thinking behind this kind of drawing — what belongs on one sheet and the pitfalls seen on site — see the guide How to draw a timing chart (in Japanese). All four editors are listed on the FA Spec Tools home page.

    10. Contact

    Please send bug reports and feature requests to yk.builds.space@gmail.com. Steps to reproduce the problem — and, if you can, the saved JSON file — make it much quicker to look into.

    개발자 후원하기

    시스템 구성도, 주소 맵, 타이밍 차트, 순서도 이 네 가지 편집기는 한 사람이 만들어 무료로 공개하고 있습니다. 제어 사양서 작성이 조금이나마 가벼워지도록 만들었습니다.
    보내 주신 후원은 그대로 다음 기능을 만드는 시간이 됩니다.

    결제해야 열리는 기능은 없고, 재촉하지도 않습니다.
    돈이 들지 않는 후원도 똑같이 도움이 됩니다 — 문제를 알리거나 기능을 제안하기 / 동료에게 이 도구를 알려 주기.

    결제는 전부 Stripe가 처리합니다. 카드 정보는 이 도구에 들어오지 않습니다.
    JSON 붙여넣기

    AI가 준 JSON을 그대로 붙여 넣으세요. 데이터 구조 사양을 따른다면 바로 그림이 됩니다.

    내보내기

    형식을 고르면 붙여 넣을 곳에 맞는 형태로 내보냅니다.

    가져오기

    어디에서 가져올지 고릅니다.

    행 표시

    축의 이동량이나 타이머의 계시값처럼 연속으로 변하는 양은 파형 쪽이 읽기 쉽습니다. 값은 지금까지처럼 셀에 넣습니다.

     눈금의 위 
    비워 두면 그 행의 값 범위에 맞춥니다. 여러 행을 견주어 볼 때는 같은 값을 넣으세요.
    화살표의 시간 조건

    원인의 변화에서 결과의 변화까지의 시간 규칙입니다(예: 검사 요구 ON에서 검사 완료 ON까지 3초 이내). 같은 신호의 ON에서 OFF로 그으면 펄스 폭이나 유지 시간이 됩니다.

    단위를 쓰지 않으면 ms입니다. 1 Step의 시간을 정해 두면 그린 지연이 조건에 맞지 않을 때 경고합니다. 순서도에서 마스터 / 슬레이브의 한쪽만 그릴 때 상한은 그 대기의 시간 초과가 됩니다.
    스텝 시간

    단위를 쓰지 않으면 ms입니다. 비우거나 1스텝의 시간과 같게 하면 개별 설정을 해제합니다. 1스텝보다 긴 스텝에는 시간 생략 표시(≈)를 그립니다.

    스텝 묶음에 이름을 붙입니다(예: 검사 중, 1사이클). 반복 구간은 마지막 스텝 다음에 첫 스텝으로 돌아갑니다(NG면 재요청, 워크마다 반복 등).

    S
    S

    S
    직선(램프)으로 채우기

     끝 값   
    선택한 범위의 각 Step에 시작 값부터 끝 값까지 일정한 비율로 값을 넣습니다. 정수 형식은 정수로 반올림합니다.